No complaints are listed for the 2015 Hino NJ8J. NHTSA's API and bulk file list none in this build.
Data build 2026-10-09.
NHTSA lists this vehicle as HINO NJ8J.
Model-generated complaint tags: No complaints are listed for tagging.
Recalls
See new recalls and investigations this week.
1 recalls.
Date: 2019-01-18. Systems: SERVICE BRAKES.
Defect: Hino Motors Sales U.S.A., Inc. (Hino) is recalling certain 2007-2019 NJ8J (258ALP) vehicles. These vehicles do not have dust shields on the front brake assemblies. During wet conditions, uneven water saturation on the front brake assemblies may result in the vehicle pulling to the left during hard braking.
Consequence: If the vehicle pulls left, it may cross into another lane unexpectedly, increasing the risk of crash.
Remedy: Hino will notify owners, and dealers will install new brake drums with dust shields, free of charge. The recall began March 19, 2019. Owners may contact Hino customer service at 1-248-699-9390. Hino's number for this recall is AACL0.
Do not drive: No. Park outside: No.
Manufacturer communications
45 manufacturer communications.
Communications by system| System | Count |
|---|
| EQUIPMENT | 17 |
|---|
| ENGINE AND ENGINE COOLING | 10 |
|---|
| ELECTRICAL SYSTEM | 9 |
|---|
| ENGINE | 6 |
|---|
| POWER TRAIN | 4 |
|---|
| EQUIPMENT ADAPTIVE/MOBILITY | 3 |
|---|
| STRUCTURE | 3 |
|---|
| FUEL SYSTEM, GASOLINE | 2 |
|---|
11000897
Date: 2024-05-17. Type: Service Bulletin/Repair Instructions. Systems: UNKNOWN OR OTHER.
After connecting to a truck using DX3, it may be necessary to review or create a DX Diagnostic Report for review.
11000898
Date: 2024-05-15. Type: Service Bulletin/Repair Instructions. Systems: UNKNOWN OR OTHER.
This article will provide dealership technicians with information on how to open a tech assist case and discuss what is required when opening a Tech Assist Case.
10159329
Date: 2019-04-11. Type: Service Bulletin/Repair Instructions. Systems: SERVICE BRAKES, HYDRAULIC.
SA-19-011 AACL0 CONVENTIONAL ALP DRUM AND DUST SHIELD PROCEDURE CHANGES
10115995
Date: 2017-02-24. Type: Service Bulletin/Repair Instructions. Systems: ELECTRICAL SYSTEM, ENGINE.
17MY vehicles contain the function to monitor PM sensor performance, however because the threshold for detection logic is not appropriate, the engine ECU may not detect a malfunction of the PM sensor. The following procedure provides direction for reprogramming the PM sensor. Certain 17MYCOE Trucks
10115994
Date: 2017-02-14. Type: Service Bulletin/Repair Instructions. Systems: ELECTRICAL SYSTEM.
Beginning with the 2017 model year, Hino changed the standard battery from a group 27 to a group 31. In the event that a group 27 battery must be replaced, it is recommended to use the group 31 as the service replacement for 2014MY and newer units. 2014MY-2016MY Hino Conventional trucks
10117649
Date: 2016-11-04. Type: Service Bulletin/Repair Instructions. Systems: STRUCTURE.
SA-14-026 The broken hood grille procedure (SB-14-020) has been revised to reuse the grille nuts (SZ17906009) if possible. There is a limited quantity of the nuts available and it has been confirmed that the nuts are reusable. The revised procedure has been posted on HinoNet. Please see the picture
10118081
Date: 2016-10-11. Type: Service Bulletin/Repair Instructions. Systems: ELECTRICAL SYSTEM, ENGINE AND ENGINE COOLING, FUEL SYSTEM, GASOLINE.
SCB-001-16 A subject vehicle may exhibit an illuminated check engine lamp with DTC (Diagnostic Trouble Code) P14BF ?EGR (Exhaust Gas Recirculation) Valve Controller Temperature Sensor 1, 2 Rationality. The EGR valve may falsely detect this rationality fault, causing the P14BF DTC to be set and store
10116051
Date: 2016-09-28. Type: Service Bulletin/Repair Instructions. Systems: ELECTRICAL SYSTEM, EQUIPMENT, TIRES.
SB - 05 - 004 SPEEDOMETER RECALIBRATION. This document is to inform of the procedure to calibrate the Pulse Adjust Module whenneeded (ex. tire size change, rear carrier ratio change).
10117750
Date: 2016-08-02. Type: Service Bulletin/Repair Instructions. Systems: ENGINE, FUEL SYSTEM, GASOLINE.
SB-16-019 An enhanced fuel cut valve is available to address a potential sticking condition that results in excess residual pressure in the dosing injector (7thinjector) supply pipe. A sticking fuel cut valve may result in the following DTC?s (diagnostic trouble codes) setting: 1. If DTC P0005 (fue
10117748
Date: 2016-04-18. Type: Service Bulletin/Repair Instructions. Systems: EQUIPMENT.
SB-16-010 Correction of the inspection of the DPR filter.