No complaints are listed for the 2014 Altec Digger Derrick. NHTSA's API and bulk file list none in this build.
Data build 2026-10-08.
NHTSA lists this vehicle as ALTEC DIGGER DERRICK.
Model-generated complaint tags: No complaints are listed for tagging.
Recalls
See new recalls and investigations this week.
8 recalls.
Date: 2025-08-29. Systems: STRUCTURE.
Defect: Altec Industries Inc. (Altec) is recalling certain 2011-2025 Aerial Device, Digger Derrick, and 2022-2025 Service Body vehicles. The cable step wire rope assembly may be improperly secured, which can allow the cable entry step to detach from the vehicle.
Consequence: A cable step that fails during use increases the risk of injury.
Remedy: Altec will provide owners with instructions to inspect the cable crimps. If the cables are improperly crimped, Altec will provide instructions and a kit to replace the wire rope assemblies. Repairs will be performed free of charge. Owner notification letters were mailed October 24, 2025. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN-3246.
Do not drive: No. Park outside: No.
Date: 2023-09-14. Systems: EQUIPMENT.
Defect: Altec Industries, Inc. (Altec) is recalling certain 2004-2023 DL42 and DL45 Digger Derricks. The incorrect hydraulic load holding valve may have been installed, which can cause the winch to lower uncontrollably and the load to fall.
Consequence: An uncontrolled load falling increases the risk of injury to personnel or others nearby.
Remedy: Altec will replace the load holding valve, free of charge. Owner notification letters are expected to be mailed October 6, 2023. Owners may contact Altec's customer service at 1-877-462-5832. Altec's number for this recall is MAB 3113.
Do not drive: No. Park outside: No.
Date: 2019-05-13. Systems: EQUIPMENT.
Defect: Altec Industries Inc. (Altec) is recalling certain 2009-2019 DL/DM, DL/DMB, DH, D/2/3/4, and DC Digger Derrick vehicles. The slope indicator placard card may falsely indicate that the unit could be used without leveling on a 5 degree slope.
Consequence: An operator may improperly set up the unit, making the unit unstable, thus increasing the risk of injury.
Remedy: Altec will notify owners, and issue CSN 719 to owners, instructing them to remove the incorrect placards, free of charge. The recall began July 2, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 719.
Do not drive: No. Park outside: No.
Date: 2019-02-27. Systems: EQUIPMENT.
Defect: Altec Industries, Inc (Altec) is recalling certain 2003-2019 Altec DL/DM, DL/DMB, and DC Digger Derrick vehicles. The pedestal tube welds may crack over time.
Consequence: Unrepaired cracks may result in failure of the pedestal and uncontrolled movement increasing the risk of injury.
Remedy: Altec will notify owners and will provide repairs as necessary and a reinforcing kit. The recall began April 3, 2019. Owners may contact Altec's customer service at 1-877-462-5832. Altec's number for this recall is CSN 713.
Do not drive: No. Park outside: No.
Date: 2018-11-09. Systems: ELECTRICAL SYSTEM.
Defect: Altec Industries, Inc. (Altec) is recalling certain 2008-2018 Altec AC18, AC23, AC26, AC30 and AC38 Cranes and D2B, D3A, D4A/B, DL42B, DT65 and DT80 Digger Derrick vehicles. The wiring on the 12V circuit from the chassis battery to the Power Distribution Module (PDM) may be insufficiently sized.
Consequence: The insufficiently sized wire may overheat, increasing the risk of fire.
Remedy: Altec will notify owners, and dealers will replace the wiring to the PDM, with a larger wire and/or replace the circuit breaker, free of charge. The recall began January 9, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 703.
Do not drive: No. Park outside: No.
Date: 2018-10-22. Systems: ELECTRICAL SYSTEM.
Defect: Altec Industries (Altec) is recalling certain 2014-2018 DHH and DHB Digger Derrick vehicles. The Zone Rating System may not alert the operator that the load being handled exceeds the rated load for the unit's specific position.
Consequence: Without an alert, there is a greater risk of unit instability or a loss of load control, increasing the risk of injury.
Remedy: Altec will notify owners and dealers will update the Zone Rating System software, free of charge. The recall began December 12, 2018. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 700.
Do not drive: No. Park outside: No.
Date: 2016-05-16. Systems: EQUIPMENT.
Defect: Altec Industries Inc. (Altec) is recalling certain model year 2014-2016 DL and DM Digger Derricks manufactured October 1, 2014, to April 30, 2016 with the digger booms mounted in the corner. The rotation bearing fasteners on the affected vehicles may not have been properly torqued.
Consequence: If the fasteners are loose or improperly torqued, structural failure may result, causing unexpected movement of the digger derrick and increasing the risk of injury.
Remedy: Altec has notified owners, and instruct them to perform the annual torque inspection, free of charge. The recall began June 2, 2016. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 633.
Do not drive: No. Park outside: No.
Date: 2015-02-23. Systems: ELECTRICAL SYSTEM.
Defect: Altec Industries Inc. (Altec) is recalling certain model year 2012-2014 Digger Derrick and Aerial Device vehicles manufactured October 1, 2012, to June 30, 2014, and mounted on Freightliner chassis. In the event of a short circuit condition, the 30 amp breaker to the trailer relay module may react too slowly to prevent the module from overheating.
Consequence: If the module overheats, there is an increased risk of a fire.
Remedy: Altec will notify owners, and dealers will replace the 30 amp circuit breaker with a 20 amp one, free of charge. The recall began on April 17, 2015. Owners may contact Altec customer service at 1-800-860-0183. Altec's number for this recall is CSN 612.
Do not drive: No. Park outside: No.
Manufacturer communications
13 manufacturer communications.
Communications by system| System | Count |
|---|
| EQUIPMENT | 6 |
|---|
| ELECTRICAL SYSTEM | 4 |
|---|
| STRUCTURE | 3 |
|---|
| UNKNOWN OR OTHER | 2 |
|---|
| ELECTRONIC STABILITY CONTROL | 1 |
|---|
| ENGINE AND ENGINE COOLING | 1 |
|---|
| EXTERIOR LIGHTING | 1 |
|---|
| PARKING BRAKE | 1 |
|---|
11019668
Date: 2025-06-18. Type: Service Bulletin/Repair Instructions. Systems: STRUCTURE, UNKNOWN OR OTHER.
Altec has learned that the king pin towing capacity placard might not be installed on certain DL derricks built from August 2005 to October 2024. This could lead to unintentional overloading which could result in cracks or deformations to the king pin assembly. Altec has had no reports of this issue
11001160
Date: 2024-06-21. Type: Service Bulletin/Repair Instructions. Systems: ELECTRICAL SYSTEM, EXTERIOR LIGHTING, UNKNOWN OR OTHER.
Altec has learned that a 12-volt Airtronics relay installed in the PDM could have been manufactured to an insufficient threshold on certain units built from December 2004 to October 2022. This can cause the relay to overheat and fail, causing the accessory lights to stop working.
10249209
Date: 2024-01-26. Type: Service Bulletin/Repair Instructions. Systems: EQUIPMENT.
Altec has learned that the cap screws used to mount the planetary winch at the turntable could be shorter than specified on certain D3000A/B and D4000A/B units built from January 2012 to December 2015.
10238374
Date: 2023-06-28. Type: Service Bulletin/Repair Instructions. Systems: EQUIPMENT.
Altec has learned that certain digger derricks and aerial devices of various models built from January 2010 to January 2023 may contain access steps with a handrail and side plate that come together in a small space causing a potential pinch point. Altec has created a kit to eliminate the possible p
10210823
Date: 2022-05-03. Type: Service Bulletin/Repair Instructions. Systems: ELECTRICAL SYSTEM.
The body compartment wiring on certain Altec aerial devices, digger derricks, and body-only units built from 2014 to 2021 contains an in-line fuse located close to the lighting in the compartment, while other units are fused upstream, closer to the power source. Altec has learned that the units affe
10210542
Date: 2022-04-29. Type: Service Bulletin/Repair Instructions. Systems: EQUIPMENT.
Altec has learned that the lift cylinder pivot pin retainers may bend or break during use on DT80 digger derricks built from March 2007 to October 2021. If the pin retainer fails, the pivot pin will still be held in place in the turntable or lower boom by retaining rings. However, the pin will be ab
10210534
Date: 2022-04-27. Type: Service Bulletin/Repair Instructions. Systems: EQUIPMENT.
Altec has learned that the electrohydraulic outrigger/tools control valve on AA755L and A-series aerial devices and DLB, DMB, and D2/3/4000B series digger derricks could have the potential to produce a very small amount of flow into the lower tools circuit when the outriggers and tools mode is engag
10209225
Date: 2022-03-18. Type: Service Bulletin/Repair Instructions. Systems: ENGINE AND ENGINE COOLING, PARKING BRAKE, POWER TRAIN.
Altec Industries, Inc. has received notification from Navistar that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with Altec equipment. On certain trucks equipped with an automatic transmission, if the automatic transmissio
10206654
Date: 2022-01-18. Type: Service Bulletin/Repair Instructions. Systems: EQUIPMENT, STRUCTURE.
Altec has learned that on certain derricks built from 2008 to 2020 the diameter of the wire winch rope installed may exceed the maximum allowable diameter specified by the ANSI A10.31 derrick standard based on the winch drum diameter. Use of an oversized wire winch rope can lead to improper rope sp
10191599
Date: 2021-04-09. Type: Service Bulletin/Repair Instructions. Systems: STRUCTURE.
Some customers have reported cracks occurring in the stationary frame tubes above the chassis frame rails of some HD35A pressure diggers built from 2005 through 2020. Investigation has shown this to be caused by improper orientation of the spacer blocks welded to the bottom of the stationary frame t